Q. How does it stick on?
A. The Megaware KeelGuard uses an advanced 3M pressure sensitive adhesive tape already bonded to the KeelGuard. By simply preparing the keel with the provided tools and primer, the KeelGuard adheres to the hull creating a permanent bond giving you years of protection and performance.
Q. Will the KeelGuard create drag and reduce the speed of my boat or PWC?
A. No, the KeelGuard is designed with hydrodynamics in mind. KeelGuard's patented drag reduction design will not slow a boat or diminish
its performance. In fact, on smaller boats and PWC's it is not uncommon to experience an increase of 1-2 miles per hour on top end speed.
Q. Does a dealer need to install the KeelGuard or can I do it myself?
A. Many of our dealers can install the KeelGuard for you or you can do it yourself. Each KeelGuard comes as a kit and has all the tools and materials for installation (a cleaning agent i.e. acetone is not supplied due to EPA shipping regulations). By following the step-by-step instructions, you can install the KeelGuard yourself in about one hour or less.
Q. Will the KeelGuard go over strakes or chines?
A. Yes, the KeelGuard material is very pliable and will easily conform to all your hull's strakes and angles.
Q. What is the KeelGuard made of?
A. The KeelGuard is a composite Polycor PVC based extrusion with special plasticizers and UV inhibitors. This material has been tested by independent laboratories and 3M, and found to provide the very best blending of abrasion resistance and bonding qualities. This combination of strength and bonding has made it possible for Megaware KeelGuard to provide the best limited lifetime warranty on the market for keel protection.
Q. Is it possible to remove the KeelGuard, and if so, will it damage the gel coat?
A. In the unlikely event you need to remove a KeelGuard, it can be done by using a heat gun and applying force. The 3M adhesive is designed to shear apart if enough strength and energy is exerted. Some of the adhesive will remain on the KeelGuard and some on the boat. The remaining adhesive can be removed from the boat with a soft putty knife and a heat gun. Or, a decal/adhesive removal disk is available from 3M.
Q. Can I apply the KeelGuard over boat bottom paint or anti-fouling paint?
A. The KeelGuard should not be applied over boat bottom or anti-fouling paint. Often times the paint will fail and pull away from the boat taking the KeelGuard along with it. Anti-fouling paints are designed to wear off over time, and for obvious reasons are not conducive for a good bonding surface. If boat bottom or anti-fouling paint is already on the boat, it should be sanded off the area where the KeelGuard will be applied. This will insure a permanent bond of the 3M adhesive. If desired, boat bottom or anti-fouling paint can be applied over the KeelGuard or after the KeelGuard has been installed.
Selected as "Editors Choice" by Trailer Boats Magazine
Chosen as one of the "top ten accessories for PWC owners" by PWC Magazine
Selected and installed by Ranger Boats for all their 1999 National Bass Federation Tournament boats.
"The KeelGuards are working out "great" in our Lethal Weapon stunt show and we would now like to put them on our boats and PWC's at Marine World."
Andrea M, Water Ski Shows, Inc.
"Installation was a breeze, I actually put it on in the parking lot of a casino in Laughlin NV. We sure like it and look at it as a small insurance policy on our investment"
Michael M. Glendale, CA
"Your product is outstanding. Recently I purchased a model 102 for my Father-in-laws' 20' Boston Whaler. Now I want to order one to install on my own."
Peter C. Miami, FL
"I recently purchased a KeelGuard for my boat and was very impressed with your product. I installed the Keelguard myself and was amazed how simple this task was to do alone. I was equally impressed with how little this product costs that could provide so much protection for a vulnerable area of my boat."
Thomas D. St. Peters, MO
