1985 Mac 25 hull thickness

A forum for discussing topics relating to older MacGregor/Venture sailboats.

Moderators: Catigale, Heath_Mod, beene, Hamin' X, kmclemore, tangentair

Post Reply
User avatar
Seadoc
Deckhand
Posts: 25
Joined: Sat Mar 04, 2017 1:52 pm
Sailboat: MacGregor 25
Location: Wytheville, VA

1985 Mac 25 hull thickness

Post by Seadoc » Tue May 07, 2019 7:24 pm

Anyone on this forum happen to know the hull thickness in the space under the V-berth on an 85 Mac 25? Also is this hull area solid fiberglass layup or might it have coring? Looking to mount a depth finder transducer inside the hull.
Thanks!

User avatar
ramirezpm
Just Enlisted
Posts: 12
Joined: Wed Aug 03, 2016 12:36 am
Sailboat: Venture 25
Location: kansas, topeka

Re: 1985 Mac 25 hull thickness

Post by ramirezpm » Wed May 08, 2019 1:08 am

I seriously doubt any core was used for the Hull of the MacGregor Boats. Core is only used in the Deck to reduce weight. More weight low down on the Boat is a good thing.

That said, have never drilled through the bottom of the Boat, so do not know the thickness of the solid fiberglass.

User avatar
Seadoc
Deckhand
Posts: 25
Joined: Sat Mar 04, 2017 1:52 pm
Sailboat: MacGregor 25
Location: Wytheville, VA

Re: 1985 Mac 25 hull thickness

Post by Seadoc » Wed May 08, 2019 3:48 pm

Thanks

User avatar
topcat0399
First Officer
Posts: 219
Joined: Sat Aug 20, 2011 7:16 pm
Sailboat: Venture 2-24
Location: Western Wisconsin, USA

Re: 1985 Mac 25 hull thickness

Post by topcat0399 » Thu May 09, 2019 7:57 am

Many of us have no trouble shooting thru the hull of a Mac.

I slapped my transducer tight in a blob of plumbers putty
and pressed it hard into the floor under the Vberth.

Works fine.

User avatar
Tomfoolery
Admiral
Posts: 5164
Joined: Tue Jul 05, 2011 9:42 am
Sailboat: MacGregor 26X
Location: Rochester, NY '99X BF50 'Tomfoolery'

Re: 1985 Mac 25 hull thickness

Post by Tomfoolery » Thu May 09, 2019 8:07 am

I've never seen a small trailer boat with a cored hull. Only big boats. FWIW.

Cored decks, yes, but not hulls. :|

User avatar
Seadoc
Deckhand
Posts: 25
Joined: Sat Mar 04, 2017 1:52 pm
Sailboat: MacGregor 25
Location: Wytheville, VA

Re: 1985 Mac 25 hull thickness

Post by Seadoc » Fri May 10, 2019 6:15 pm

My appreciation for those who have replied.

THE CUSCUS
First Officer
Posts: 327
Joined: Fri Sep 11, 2009 9:59 am
Sailboat: Venture 25
Location: North East River, MD

Re: 1985 Mac 25 hull thickness

Post by THE CUSCUS » Tue May 14, 2019 10:30 am

Mac hulls are definitely not cored. The hull under the V-berth does get thicker the closer you get to the bottom of the "V". I have my depth transducer mounted about a foot up the starboard side from the bottom of the "V", directly under the access hatch in the rear of the V-berth.

Post Reply